How to Fix Arlo Camera Red Light Blinking issue?

Arlo security cameras are well-known for their dependable monitoring, simple setup, and excellent video streaming. But like any technological gadget, Arlo cameras can occasionally have problems. The arlo camera red light blinking is one of the recurrent subjects consumers come across. This red light that blinks might be alarming as it means that there is a problem with the camera’s operation and it isn’t working correctly.

We’ll go over the potential causes of your Arlo camera’s red light flashing problem in this blog, along with comprehensive instructions on how to diagnose and fix it. This article will assist you in resolving the problem and getting your Arlo camera to function again, regardless of your level of experience.

Comprehending Arlo Camera’s Red Light

It’s critical to comprehend the meaning of the red light on your Arlo camera before beginning any troubleshooting. The device’s red blinking light usually signifies a malfunction, usually related to power or connectivity problems. When arlo camera red light blinking, different Arlo camera types may behave differently, but generally speaking, it indicates the following typical problems:

Low Battery: It’s possible that the battery in your camera is almost dead.
Connectivity Issues: Your Wi-Fi connection may be having trouble, or there may be interference between your network and the camera.
A firmware update is required: Occasionally, when the firmware has to be updated, Arlo cameras may glow red.
System or Hardware Failure: The red light might potentially be caused by a hardware issue with the camera.

How to Fix red blinking light on arlo camera?

Follow the tips given here to analyse the issue and get the solution:

1. First, determine the battery level.

A dead or low battery is one of common grounds of arlo camera red light blinking. The red blinking light indicates that your camera’s battery needs to be charged or changed if it runs on batteries.

Open the Arlo app to check the battery level.
Use the provided charging cord to recharge the battery if it’s low, or get a new one.
The red light ought to go off once the battery has been charged or changed, and your camera will then work normally.

2. Turn Your Arlo Camera Back On

The arlo camera red light blinking is one of several technical issues that can occasionally be fixed with a simple reboot.

Rebooting your Arlo camera is the solution.
The camera should be taken out of its mount.
Holding down the power knob will turn it off.
After a few seconds, hit the power knob once again to turn the camera back on.
In addition to refreshing the system, this may fix small problems like software bugs or brief network connectivity difficulties.

3. Verify the Wi-Fi connection

The red blinking light on arlo camera indicates that there is a poor or interrupted Wi-Fi connection. This is particularly prevalent if your home is vast, your walls are thick, or there are other gadgets interfering with the camera and your Wi-Fi router.

Make sure the area where the camera is positioned has a strong Wi-Fi signal.
By bringing the camera closer to the router and seeing if the red light stops flashing, you may check the strength of the Wi-Fi connection.
If this fixes it, you could need to move your router or think about utilizing a Wi-Fi extender to strengthen the signal in the locations where your camera is situated.
Consider moving your camera or router, or use a Wi-Fi mesh system to increase coverage in difficult-to-reach places, if the camera’s signal is too weak.

4. Firmware Update for the Camera

The arlo camera red light blinking is one of several problems that might be caused by outdated firmware. Frequent firmware upgrades address known problems, increase security, and improve camera performance.

Launch the app and complete arlo login, go to the settings menu, and see if there are any firmware upgrades for your camera.
Let the update download and install if there is one.
The camera may restart itself at this time, which might take several minutes.
After updating the firmware, see whether the red blinking light goes away.

Go on to the next troubleshooting steps if the problem persists.

5. Connect the Base Station and Camera

The arlo camera red light blinking may appear if your camera and base station are not synchronizing properly. It’s possible that the camera isn’t configured properly or that it lost contact with the base station.

Re-syncing the camera with the base station.
Hold down the base station’s sync button until the blue blinking LED light appears.
Then, once the camera’s LED begins to blink amber, press and hold the sync button.
Await the completion of the synchronization procedure. Once the camera has properly synchronized with the base station, its LED light should turn solid blue.

6. Return the camera to its original configuration.

Resetting the camera to its factory settings could be necessary if all else fails and arlo camera red light blinking continues. This should only be done as a last option because it will remove all of the camera’s settings and data.

The Arlo camera may be reset by pressing and holding the reset button for ten seconds or so, or until the amber LED blinks.
The camera will resume when the reset is finished.
The Arlo app now allows you to re-configure the camera.

7. Speak with our experts

There could be a more serious hardware or software problem with the camera if you’ve attempted all of the aforementioned fixes and still arlo camera red light blinking. For more help in this situation, it’s time to get in touch with us.

Use our website to contact us.
Our professionals can back you in categorizing the problem and deciding whether to replace or repair your camera.

Preventive Steps to Steer Clear of the Red Light Problem

Here are some pointers to prevent red blinking lights from happening frequently:

To guarantee that the camera always has adequate power, charge the battery on a regular basis or replace it as necessary.
By positioning the camera in the best possible spot, minimizing interference, and, if required, utilizing a mesh system, you can maintain a robust Wi-Fi connection.
Update your firmware to avoid compatibility problems or glitches.
To make sure the camera is still functioning as intended, test it from time to time.

Conclusion

Your arlo camera red light blinking might be annoying, but you can easily fix it with the correct troubleshooting techniques. You may restore your Arlo camera to normal by following the instructions in this article, regardless of whether the issue is caused by a low battery, communication issues, or a software upgrade.